Persyaratan Mutu Karet Afrika Selatan   

Ketentuan Impor Produk Karet.

  • Karet dalam bentuk primer atau pelat, lembaran atau strip, memerlukan izin impor dari ITAC
  • Limbah, potongan karet, memerlukan izin impor dari ITAC
  • Ban pneumatik baru, dari karet, memerlukan izin impor dari ITAC
  • Ban karet pneumatik yang ditata ulang atau bekas, memerlukan izin impor dari ITAC
  • Barang lainnya dari karet vulkanisir, diperlukan letter of approval dari SABS, lihat Regulasi SABS: Komponen Otomotif

Regulasi terkait dengan produk karet:

  • Government Notice No. 988, Gazette No 35927 of 30 November 2012 tentang Rencana Pengelolaan Ban Limbah Industri Terpadu dari Prakarsa Daur Ulang dan Pengembangan Ekonomi Afrika Selatan
  • Hazardous Substances Act 1973 (Act No. 15 of 1973)
  • Agricultural Pests Act 28/1974 ( Act No. 36/1983)

Standar Produk Karet.

SABS (The South African Bureau of Standards) menyediakan standar yang mencakup tuntutan industri karet dan plastik, mulai dari sistem manajemen mutu hingga metode pengujian bahan atau suku cadang tertentu.
Standar ini dapat membantu produsen/importir untuk meningkatkan kepuasan pelanggan, memenuhi persyaratan peraturan, keselamatan dan keandalan, dan memastikan konsistensi kualitas pada seluruh rantai pasokan.
  • SANS 492-4 Protective and safety gum boots Part 4: Moulded rubber ankle boots for men
  • SANS 492-3 Protective and safety gum boots Part 3: Handmade rubber ankle boots for men
  • SANS 764 Rubber garden hose
  • SANS 5661 Determination of adhesion of upper leather to direct moulded rubber soling material
  • SANS 1701-5-10 Bearings Part 5: Pedestal bearings and structural bearings Section 10: Rubber products - Bridge bearings - Specification for rubber materials
  • SANS 1437 Footwear soling material and footwear sole and heel components of rubber and plastics
  • SANS 4074-6 Rubber condoms Part 6: Determination of bursting volume and pressure
  • SANS 4074-7 Rubber condoms Part 7: Oven conditioning
  • SANS 4074-9 Rubber condoms Part 9: Determination of tensile properties
  • SANS 1155 The manufacture of surgical rubber gloves (single use)
  • SANS 492-2 Protective and safety gum boots Part 2: Moulded rubber gum boots
  • SANS 50681-1 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber
  • SANS 492-1 Protective and safety gum boots Part 1: Handmade rubber gum boots
  • SANS 1421 Rubber- or plastics-coated fabrics - Determination of tensile strength and elongation at break
  • SANS 4661-2 Rubber, vulcanized - Preparation of samples and test pieces Part 2: Chemical tests
  • SANS 11431-1 Rubber, vulcanized or thermoplastic - Resistance to ozone cracking Part 1: Static strain test
  • SANS 11431-3 Rubber, vulcanized or thermoplastic - Resistance to ozone cracking Part 3: Reference and alternative methods for determining the ozone concentration in laboratory test chambers
  • SANS 11346 Rubber, vulcanized or thermoplastic - Estimation of life-time and maximum temperature of use from an Arrhenius plot
  • SANS 7743 Rubber, vulcanized or thermoplastic - Determination of compression stress-strain properties
  • SANS 11432 Rubber, vulcanized or thermoplastic - Determination of low temperature stiffening (Gehman test)
  • SANS 10815 Rubber, vulcanized or thermoplastic - Determination of compression set at ambient, elevated or low temperatures
  • SANS 2878 Rubber - Antistatic and conductive products - Determination of electrical resistance
  • SANS 11817 Rubber, vulcanized - Determination of the effect of liquids
  • SANS 6471 Rubber, vulcanized - Determination of crystallization effects under compression
  • SANS 11345 Rubber - Assessment of carbon black dispersion - Rapid comparative methods
  • SANS 2883 Rubber, vulcanized - Antistatic and conductive products for industrial use - Electrical resistance limits
  • SANS 2230 Rubber products - Guidelines for storage
  • SANS 4663 Rubber - Determination of dynamic behaviour of vulcanizates at low frequencies - Torsion pendulum method
  • SANS 4662 Rubber, vulcanized or thermoplastic - Determination of rebound resilience
  • SANS 7619 Rubber - Determination of indentation hardness by means of pocket hardness meters
  • SANS 4649 Rubber, vulcanized or thermoplastic - Determination of abrasion resistance using a rotating cylindrical drum device
  • SANS 3387 Rubber - Determination of crystallization effects by hardness measurements
  • SANS 3302-1 Rubber - Tolerances for products Part 1: Dimensional tolerances
  • SANS 3302-2 Rubber - Tolerances for products Part 2: Geometrical tolerances
  • SANS 9272 Rubber and rubber products - Determination of precision for test method standards
  • SANS 471 Rubber - Temperatures, humidities and times for conditioning and testing
  • SANS 4664 Rubber - Guide to the determination of dynamic properties
  • SANS 5893 Rubber and plastics test equipment - Tensile, flexural and compression types (constant rate of traverse) - Specification
  • SANS 11853 Conducting and dissipative rubbers, vulcanized or thermoplastic - Measurement of resistivity
  • SANS 16133 Rubber and plastics - Analysis of multipeak traces obtained in determinations of tear strength and adhesion strength
  • SANS 2781 Rubber, vulcanized or thermoplastic - Determination of density
  • SANS 2882 Rubber, vulcanized - Antistatic and conductive products for hospital use - Electrical resistance limits
  • SANS 4074 Natural latex rubber condoms - Requirements and test methods
  • SANS 16037 Rubber condoms for clinical trials - Measurement of physical properties
  • SANS 68 Single-use sterile rubber surgical gloves - Specification
  • SANS 1036 Rubber, vulcanized or thermoplastic - Determination of adhesion to textile fabrics
  • SANS 3450 Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems
  • SANS 1198 The manufacture of rubber sheeting for rubber lining
  • SANS 1201 The application of rubber linings to pipes, pipe fittings and vessels
  • SANS 3821 Gas welding equipment - Rubber hoses for welding, cutting and allied processes
  • SANS 4635 Rubber, vulcanized - Preformed compression seals for use between concrete motorway paving sections - Specification for material
  • SANS 1411 Gas welding equipment - Rubber and plastic hoses assembled for compressed or liquefied gases up to a maximum design pressure of 450 bar
  • SANS 4648 Rubber, vulcanized or thermoplastic - Determination of dimensions of test pieces and products for test purposes
  • SANS 6446 Rubber products - Bridge bearings - Specification for rubber materials
  • SANS 974-3 Rubber joint rings (non-cellular) Part 3: Joint rings for use in pressure cookers
  • SANS 5871 Rebound resilience of vulcanized rubbers (Lupke Pendulum method)
  • SANS 5874 Resistance of vulcanized rubbers to flex cracking (De Mattia method)
  • SANS 5877 Heat resistance of vulcanized rubbers
  • SANS 5878 Low temperature resistance of vulcanized rubbers
  • SANS 5879 Resistance to flaming of vulcanized rubbers
  • SANS 272 Rubber hoses, textile-reinforced, for general-purpose water applications - Specification
  • SANS 1574-4 Electric flexible cables with solid extruded dielectric insulation Part 4: Rubber-insulated cables for domestic, office and similar environments (cords)
  • SANS 4661-1 Rubber, vulcanized or thermoplastic - Preparation of samples and test pieces Part 1: Physical tests
  • SANS 1574-5
  • Electric flexible cables with solid extruded dielectric insulation Part 5: Rubber-insulated cables for industrial use
  • SANS 484-1 Conveyor belting - Step splicing for multi-ply textile-reinforced rubber covered conveyor belting Part 1: Hot-splicing method
  • SANS 16038 Rubber condoms - Guidance on the use of ISO 4074 in the quality management of natural rubber latex condoms
  • SANS 23529 Rubber - General procedures for preparing and conditioning test pieces for physical test methods
  • SANS 8009 Mechanical contraceptives - Reusable natural and silicone rubber contraceptive diaphragms - Requirements and tests
  • SANS 4642 Rubber products - Hoses, non-collapsible, for fire-fighting service
  • SANS 14557 Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies
  • SANS 8009-1 Reusable rubber contraceptive diaphragms Part 1: Classification, sampling and requirements
  • SANS 8009-10 Reusable rubber contraceptive diaphragms Part 10: Recommendations for storage
  • SANS 8009-2 Reusable rubber contraceptive diaphragms Part 2: Determination of size
  • SANS 8009-3
  • Reusable rubber contraceptive diaphragms Part 3: Determination of dome thickness
  • SANS 8009-4 Reusable rubber contraceptive diaphragms Part 4: Freedom from visible defects
  • SANS 8009-5 Reusable rubber contraceptive diaphragms Part 5: Determination of tensile properties
  • SANS 8009-6 Reusable rubber contraceptive diaphragms Part 6: Determination of deterioration after accelerated ageing
  • SANS 8009-7 Reusable rubber contraceptive diaphragms Part 7: Determination of compression resistance of coil spring and flat spring diaphragms
  • SANS 8009-8 Reusable rubber contraceptive diaphragms Part 8: Determination of twisting during compression of coil spring and flat spring diaphragms
  • SANS 8009-9 Reusable rubber contraceptive diaphragms Part 9: Packaging and labelling
  • SANS 576 Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling - Specification
  • SANS 2398 Rubber hoses, textile-reinforced, for compressed-air - Specification
  • SANS 4633 Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials
  • SANS 187 Butyl rubber sheet (for waterproofing)
  • SANS 580 Chloroprene rubber sheet (for waterproofing)
  • SANS 564 Rubber insertion sheeting
  • SANS 988 Braided reinforced rubber hose for air and water
  • SANS 1321-2 Non-metallic waste traps Part 2: Rubber waste traps
  • SANS 974-2 Rubber joint rings (non-cellular) Part 2: Joint rings for use in the dairy industry
  • SANS 4074-1 Rubber condoms Part 1: Requirements
  • SANS 4074-10 Rubber condoms Part 10: Packaging and labelling - Condoms in consumer packages
  • SANS 4074-2 Rubber condoms Part 2: Determination of length
  • SANS 4074-3 Rubber condoms Part 3: Determination of width
  • SANS 4074-5 Rubber condoms Part 5: Testing for holes - Water leak test
  • SANS 5876 Ozone resistance of vulcanized rubbers (RAPRA-Hampden method)
  • SANS 5867 Preparation of samples of vulcanized rubbers for testing
  • SANS 5868 Conditioning of vulcanized rubbers
  • SANS 5870 Hardness of vulcanized rubbers of hardness 30-95 IRH degrees
  • SANS 5872 Compression set of vulcanized rubbers under constant deflection
  • SANS 5873 Tear strength of vulcanized rubbers
  • SANS 5880 Electrical resistance of vulcanized rubbers
  • SANS 5881 Solvent extractable content of vulcanized rubbers
  • SANS 5882 Resistance of vulcanized rubbers to chemicals (liquids and solutions)
  • SANS 5503 Preparation of test pieces for tensile tests on cable dielectric and sheathing, and tear tests on rubber sheathing
  • SANS 5504 Tensile strength and elongation at break of rubber and plastics electric cable materials
  • SANS 5505 Tension set of rubber electric cable dielectric and sheathing
  • SANS 5508 Accelerated aging of rubber cable dielectric and sheathing by the oxygen pressure chamber method
  • SANS 1305 Sealing compounds for the building industry, one-component, silicone-rubber-base
  • SANS 11193 Single-use rubber examination gloves - Specification
  • SANS 5506 Tear resistance of rubber cable sheathing
  • SANS 5883 Resistance of vulcanized rubbers to swelling (volumetric method)
  • SANS 5875 Water absorption of vulcanized rubbers
  • SANS 5869 Accelerated aging of vulcanized rubbers (Air-oven method)
  • SANS 484-2 Conveyor belting - Step splicing for multi-ply textile-reinforced rubber covered conveyor belting Part 2: Cold-splicing method
  • SANS 10048 Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD)
  • SANS 10037 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties
  • SANS 1132 Rubber, vulcanized or thermoplastic - Determination of flex cracking and crack growth (De Mattia)
  • SANS 54 Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests
  • SANS 10034-1 Rubber, vulcanized or thermoplastic - Determination of tear strength Part 1: Trouser, angle and crescent test pieces
  • SANS 10034-2 Rubber, vulcanized or thermoplastic - Determination of tear strength Part 2: Small (Delft) test pieces
  • SANS 10815-1 Rubber, vulcanized or thermoplastic - Determination of compression set Part 1: At ambient or elevated temperatures
  • SANS 10815-2 Rubber, vulcanized or thermoplastic - Determination of compression set Part 2: At low temperatures
  • SANS 11407 Rubber - Determination of solvent extract
  • SANS 11431-2 Rubber, vulcanized or thermoplastic - Resistance to ozone cracking Part 2: Dynamic strain test
  • SANS 7619-1 Rubber, vulcanized or thermoplastic - Determination of indentation hardness Part 1: Durometer method (Shore hardness)
  • SANS 7619-2 Rubber, vulcanized or thermoplastic - Determination of indentation hardness Part 2: IRHD pocket meter method
  • SANS 6805 Rubber hoses and hose assemblies for underground mining - Wire-reinforced hydraulic types for coal mining - Specification
  • SANS 18752 Rubber hoses and hose assemblies - Wire- or textile-reinforced single-pressure types for hydraulic applications - Specification
  • SANS 28017 Rubber hoses and hose assemblies, Wire or textile reinforced, for dredging applications - Specification
  • SANS 254 Earth-moving machinery - Rubber-tyred machines - Steering requirements
  • SANS 3383 Rubber - General directions for achieving elevated or subnormal temperatures for test purposes
  • SANS 11193-1 Single-use medical examination gloves Part 1: Specification for gloves made from rubber latex or rubber solution
  • SANS 4642-1 Rubber and plastics hoses, non-collapsible, for fire-fighting service Part 1: Semi-rigid hoses for fixed systems
  • SANS 4642-2 Rubber and plastics hoses, non-collapsible, for fire-fighting service Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles
  • SANS 4664-1 Rubber, vulcanized or thermoplastic - Determination of dynamic properties Part 1: General guidance
  • SANS 4664-2 Rubber, vulcanized or thermoplastic - Determination of dynamic properties Part 2: Torsion pendulum methods at low frequencies
  • SANS 974-1 Rubber joint rings (non-cellular) Part 1: Joint rings for use in water, sewer and drainage systems
 

Standar Internasional

Standar internasional yang dapat dijadikan rujukan.
  • ISO 34-1:2015 Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 1: Trouser, angle and crescent test pieces
  • ISO 34-2:2015 Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 2: Small (Delft) test pieces
  • ISO 36:2020 Rubber, vulcanized or thermoplastic — Determination of adhesion to textile fabrics
  • ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
  • ISO 48-1:2018 Rubber, vulcanized or thermoplastic — Determination of hardness — Part 1: Introduction and guidance
  • ISO 48-2:2018 Rubber, vulcanized or thermoplastic — Determination of hardness — Part 2: Hardness between 10 IRHD and 100 IRHD
  • ISO 48-3:2018 Rubber, vulcanized or thermoplastic — Determination of hardness — Part 3: Dead-load hardness using the very low rubber hardness (VLRH) scale
  • ISO 48-4:2018 Rubber, vulcanized or thermoplastic — Determination of hardness — Part 4: Indentation hardness by durometer method (Shore hardness)
  • ISO 48-5:2018 Rubber, vulcanized or thermoplastic — Determination of hardness — Part 5: Indentation hardness by IRHD pocket meter method
  • ISO 48-9:2018 Rubber, vulcanized or thermoplastic — Determination of hardness — Part 9: Calibration and verification of hardness testers
  • ISO 132:2017 Rubber, vulcanized or thermoplastic — Determination of flex cracking and crack growth (De Mattia)
  • ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
  • ISO/WD 188 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
  • ISO 247-1:2018 Rubber — Determination of ash — Part 1: Combustion method
  • ISO 247-2:2018 Rubber — Determination of ash — Part 2: Thermogravimetric analysis (TGA)
  • ISO 289-1:2015 Rubber, unvulcanized — Determinations using a shearing-disc viscometer — Part 1: Determination of Mooney viscosity
  • ISO 289-2:2020 Rubber, unvulcanized — Determinations using a shearing-disc viscometer — Part 2: Determination of pre-vulcanization characteristics
  • ISO 289-3:2015 Rubber, unvulcanized — Determinations using a shearing-disc viscometer — Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR
  • ISO/TS 289-4:2017 Rubber, unvulcanized — Determinations using a shearing-disc viscometer — Part 4: Determination of the Mooney stress-relaxation rate
  • ISO 812:2017 Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness
  • ISO 813:2019 Rubber, vulcanized or thermoplastic — Determination of adhesion to a rigid substrate — 90 degree peel method
  • ISO 814:2017 Rubber, vulcanized or thermoplastic — Determination of adhesion to metal — Two-plate method
  • ISO 815-1:2019 Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures
  • ISO 815-2:2019 Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures
  • ISO 1382:2012 Rubber — Vocabulary
  • ISO/FDIS 1382 Rubber — Vocabulary
  • ISO 1407:2011 Rubber — Determination of solvent extract
  • ISO 1408:1995 Rubber — Determination of carbon black content — Pyrolytic and chemical degradation methods
  • ISO/CD 1431-1 Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing
  • ISO 1431-1:2012 Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing
  • ISO 1431-3:2017 Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 3: Reference and alternative methods for determining the ozone concentration in laboratory test chambers
  • ISO 1432:2013 Rubber, vulcanized or thermoplastic — Determination of low-temperature stiffening (Gehman test)
  • ISO/DIS 1432 Rubber, vulcanized or thermoplastic — Determination of low-temperature stiffening (Gehman test)
  • ISO 1434:2016 Natural rubber in bales — Amount of bale coating — Determination
  • ISO 1629:2013 Rubber and latices — Nomenclature
  • ISO 1658:2015 Natural rubber (NR) — Evaluation procedure
  • ISO/WD 1658 Natural rubber (NR) — Evaluation procedure
  • ISO 1817:2015 Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
  • ISO/WD 1817 Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
  • ISO 1827:2016 Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods
  • ISO 1853:2018 Conducting and dissipative rubbers, vulcanized or thermoplastic — Measurement of resistivity
  • ISO 2007:2018 Rubber, unvulcanized — Determination of plasticity — Rapid-plastimeter method
  • ISO 2230:2002 Rubber products — Guidelines for storage
  • ISO 2285:2019 Rubber, vulcanized or thermoplastic — Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load
  • ISO 2302:2014 Isobutene-isoprene rubber (IIR) — Evaluation procedure
  • ISO/FDIS 2302 Isobutene-isoprene rubber (IIR) — Evaluation procedure
  • ISO 2303:2019 Isoprene rubber (IR) — Non-oil-extended, solution-polymerized types — Evaluation procedures
  • ISO 2322:2014 Styrene-butadiene rubber (SBR) — Emulsion- and solution-polymerized types — Evaluation procedures
  • ISO 2393:2014 Rubber test mixes — Preparation, mixing and vulcanization — Equipment and procedures
  • ISO 2454:1995 Rubber products — Determination of zinc content — EDTA titrimetric method
  • ISO 2475:2011 Chloroprene rubber (CR) — General-purpose types — Evaluation procedure
  • ISO 2476:2014 Butadiene rubber (BR) — Solution-polymerized types — Evaluation procedures
  • ISO 2781:2018 Rubber, vulcanized or thermoplastic — Determination of density
  • ISO 2782-1:2016 Rubber, vulcanized or thermoplastic — Determination of permeability to gases — Part 1: Differential-pressure methods
  • ISO 2782-2:2018 Rubber, vulcanized or thermoplastic — Determination of permeability to gases — Part 2: Equal-pressure method
  • ISO 2878:2017 Rubber, vulcanized or thermoplastic — Antistatic and conductive products — Determination of electrical resistance
  • ISO 2921:2019 Rubber, vulcanized — Determination of low-temperature characteristics — Temperature-retraction procedure (TR test)
  • ISO 2951:2019 Rubber, vulcanized rubber — Determination of insulation resistance
  • ISO 3384-1:2019 Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression — Part 1: Testing at constant temperature
  • ISO 3384-2:2019 Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression — Part 2: Testing with temperature cycling
  • ISO 3387:2020 Rubber — Determination of crystallization effects by hardness measurements
  • ISO 3865:2020 Rubber, vulcanized or thermoplastic — Methods of test for staining in contact with organic material
  • ISO 4097:2014 Rubber, ethylene-propylene-diene (EPDM) — Evaluation procedure
  • ISO/PRF 4097 Rubber, ethylene-propylene-diene (EPDM) — Evaluation procedure
  • ISO 4645:1984 Rubber and rubber products — Guide to the identification of antidegradants — Thin layer chromatographic methods
  • ISO 4645:1984/COR 1:1991 Rubber and rubber products — Guide to the identification of antidegradants — Thin layer chromatographic methods — Technical Corrigendum 1
  • ISO 4647:2010 Rubber, vulcanized — Determination of static adhesion to textile cord — H-pull test
  • ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
  • ISO 4650:2012 Rubber — Identification — Infrared spectrometric methods
  • ISO 4658:1999 Acrylonitrile-butadiene rubber (NBR) — Evaluation procedure
  • ISO 4658:1999/AMD 1:2004 Acrylonitrile-butadiene rubber (NBR) — Evaluation procedure — Amendment 1
  • ISO/PRF 4658 Acrylonitrile-butadiene rubber (NBR) — Evaluation procedure
  • ISO/PRF 4659 Styrene-butadiene rubber (carbon black or carbon black and oil masterbatches) — Evaluation procedure
  • ISO 4659:2014 Styrene-butadiene rubber (carbon black or carbon black and oil masterbatches) — Evaluation procedure
  • ISO 4661-2:2018 Rubber, vulcanized — Preparation of samples and test pieces — Part 2: Chemical tests
  • ISO 4662:2017 Rubber, vulcanized or thermoplastic — Determination of rebound resilience
  • ISO 4664-1:2011 Rubber, vulcanized or thermoplastic — Determination of dynamic properties — Part 1: General guidance
  • ISO/WD 4664-1 Rubber, vulcanized or thermoplastic — Determination of dynamic properties — Part 1: General guidance
  • ISO 4664-2:2006 Rubber, vulcanized or thermoplastic — Determination of dynamic properties — Part 2: Torsion pendulum methods at low frequencies
  • ISO/DIS 4664-3 Rubber, vulcanized or thermoplastic — Determination of dynamic properties — Part 3: Glass transition temperature (Tg)
  • ISO 4665:2016 Rubber, vulcanized or thermoplastic — Resistance to weathering
  • ISO 4666-1:2010 Rubber, vulcanized — Determination of temperature rise and resistance to fatigue in flexometer testing — Part 1: Basic principles
  • ISO 4666-3:2016 Rubber, vulcanized — Determination of temperature rise and resistance to fatigue in flexometer testing — Part 3: Compression flexometer (constant-strain type)
  • ISO 4666-4:2018 Rubber, vulcanized — Determination of temperature rise and resistance to fatigue in flexometer testing — Part 4: Constant-stress flexometer
  • ISO 5600:2017 Rubber — Determination of adhesion to rigid materials using conical shaped parts
  • ISO 5603:2017 Rubber, vulcanized — Determination of adhesion to wire cord
  • ISO 6101-1:2019 Rubber — Determination of metal content by atomic absorption spectrometry — Part 1: Determination of zinc content
  • ISO 6101-2:2019 Rubber — Determination of metal content by atomic absorption spectrometry — Part 2: Determination of lead content
  • ISO 6101-3:2014 Rubber — Determination of metal content by atomic absorption spectrometry — Part 3: Determination of copper content
  • ISO/CD 6101-3 Rubber — Determination of metal content by atomic absorption spectrometry — Part 3: Determination of copper content
  • ISO 6101-4:2014 Rubber — Determination of metal content by atomic absorption spectrometry — Part 4: Determination of manganese content
  • ISO/CD 6101-4 Rubber — Determination of metal content by atomic absorption spectrometry — Part 4: Determination of manganese content
  • ISO 6101-5:2018 Rubber — Determination of metal content by atomic absorption spectrometry — Part 5: Determination of iron content
  • ISO 6101-6:2018 Rubber — Determination of metal content by atomic absorption spectrometry — Part 6: Determination of magnesium content
  • ISO 6133:2015 Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength
  • ISO 6502-1:2018 Rubber — Measurement of vulcanization characteristics using curemeters — Part 1: Introduction
  • ISO 6502-2:2018 Rubber — Measurement of vulcanization characteristics using curemeters — Part 2: Oscillating disc curemeter
  • ISO 6502-3:2018 Rubber — Measurement of vulcanization characteristics using curemeters — Part 3: Rotorless curemeter
  • ISO 6505:2015 Rubber, vulcanized or thermoplastic — Determination of tendency to adhere to and corrode metals
  • ISO 6914:2013 Rubber, vulcanized or thermoplastic — Determination of ageing characteristics by measurement of stress relaxation in tension
  • ISO/DIS 6914 Rubber, vulcanized or thermoplastic — Determination of ageing characteristics by measurement of stress relaxation in tension
  • ISO 6943:2017 Rubber, vulcanized — Determination of tension fatigue
  • ISO 7269:1995 Rubber — Determination of free sulfur
  • ISO 7269:1995/COR 1:2002 Rubber — Determination of free sulfur — Technical Corrigendum 1
  • ISO 7270-1:2020 Rubber — Analysis by pyrolytic gas-chromatographic methods — Part 1: Identification of polymers (single polymers and polymer blends)
  • ISO 7270-2:2012 Rubber — Analysis by pyrolytic gas-chromatographic methods — Part 2: Determination of styrene/butadiene/isoprene ratio
  • ISO 7323:2006 Rubber, raw and unvulcanized compounded — Determination of plasticity number and recovery number — Parallel-plate method
  • ISO/TR 7620:2005 Rubber materials — Chemical resistance
  • ISO 7663:2014 Halogenated isobutene-isoprene rubber (BIIR and CIIR) — Evaluation procedures
  • ISO 7725:2020 Rubber and rubber products — Determination of chlorine and bromine content
  • ISO 7743:2017 Rubber, vulcanized or thermoplastic — Determination of compression stress-strain properties
  • ISO 7780:1998 Rubbers and rubber latices — Determination of manganese content — Sodium periodate photometric methods
  • ISO 8013:2019 Rubber, vulcanized — Determination of creep in compression or shear
  • ISO 8053:1995 Rubber and latex — Determination of copper content — Photometric method
  • ISO 9026:2007 Raw rubber or unvulcanized compounds — Determination of green strength
  • ISO 9028:2006 Rubber — Dissolution by acid digestion
  • ISO 9924-1:2016 Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrene-butadiene rubbers
  • ISO 9924-2:2016 Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 2: Acrylonitrile-butadiene and halobutyl rubbers
  • ISO 9924-3:2009 Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 3: Hydrocarbon rubbers, halogenated rubbers and polysiloxane rubbers after extraction
  • ISO 10398:1998 Rubber — Identification of accelerators in cured and uncured compounds
  • ISO 11345:2006 Rubber — Assessment of carbon black and carbon black/silica dispersion — Rapid comparative methods
  • ISO 11346:2014 Rubber, vulcanized or thermoplastic — Estimation of life-time and maximum temperature of use
  • ISO/WD 11346 Rubber, vulcanized or thermoplastic — Estimation of life-time and maximum temperature of use
  • ISO/TR 12134:2010 Rubber — Estimation of uncertainty for test methods — Non-functional parameters
  • ISO 12493:2017 Rubber, vulcanized — Determination of stress in tension upon heating
  • ISO/WD 12493 Rubber, vulcanized — Determination of stress in tension upon heating
  • ISO 12965:2000 Butadiene rubber — Determination of microstructure by infra-red spectrometry
  • ISO 12965:2000/COR 1:2006 Butadiene rubber — Determination of microstructure by infra-red spectrometry — Technical Corrigendum 1
  • ISO 13145:2012 Rubber — Determination of viscosity and stress relaxation using a rotorless sealed shear rheometer
  • ISO 13226:2018 Rubber — Standard reference elastomers (SREs) for characterizing the effect of liquids on vulcanized rubbers
  • ISO 13507:2012 Rubber compounds, raw rubbers and compounding materials — Short terms for properties reported in certificates of analysis
  • ISO 14309:2019 Rubber, vulcanized or thermoplastic — Determination of volume and/or surface resistivity
  • ISO 14558:2016 Rubber — Determination of residual unsaturation of hydrogenated nitrile butadiene rubber (HNBR) by infrared spectroscopy
  • ISO 15113:2005 Rubber — Determination of frictional properties
  • ISO 15671:2000 Rubber and rubber additives — Determination of total sulfur content using an automatic analyser
  • ISO/DIS 15671 Rubber and rubber products — Determination of total sulfur content using an automatic analyser
  • ISO 15672:2000 Rubber and rubber additives — Determination of total nitrogen content using an automatic analyser
  • ISO 16565:2013 Rubber — Determination of 5-ethylidenenorbornene (ENB) or dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers
  • ISO/TR 17051 Rubber, vulcanized — Guidelines for material specification
  • ISO 17257:2020 Rubber — Identification of polymers — Pyrolytic gas-chromatographic method using mass-spectrometric detection
  • ISO 17564:2008 Raw hydrogenated nitrile rubber (HNBR) — Determination of residual unsaturation by iodine value
  • ISO/TS 17796:2013 Rubber — Trapping and identification of volatile components of rubber fumes with active sampling on a poly(2,6-diphenylphenylene oxide) type sorbent, using thermodesorption and gas chromatographic method with mass spectrometric detection
  • ISO 18766:2014 Rubber, vulcanized or thermoplastic — Low temperature testing — General introduction and guide
  • ISO 18899:2013 Rubber — Guide to the calibration of test equipment
  • ISO 19003:2006 Rubber and rubber products — Guidance on the application of statistics to physical testing
  • ISO 19051:2015 Rubber, raw natural, and rubber latex, natural — Determination of nitrogen content by Micro Dumas combustion method
  • ISO 19242:2015 Rubber — Determination of total sulfur content by ion chromatography
  • ISO 19983:2017 Rubber — Determination of precision of test methods
  • ISO/CD 19983 Rubber — Determination of precision of test methods
  • ISO 19984-1:2017 Rubber and rubber products — Determination of biobased content — Part 1: General principles and calculation methods using the formulation of the rubber compound
  • ISO 19984-2:2017 Rubber and rubber products — Determination of biobased content — Part 2: Biobased carbon content
  • ISO 19984-3:2017 Rubber and rubber products — Determination of biobased content — Part 3: Biobased mass content
  • ISO 20163:2019 Vulcanized rubber — Determination of free sulfur by gas chromatography (GC) and high performance liquid chromatography (HPLC)
  • ISO 20463:2018 Rubber and rubber products — Determination of combustion energy and carbon dioxide emission from biobased and non-biobased materials
  • ISO/TS 21396:2017 Rubber — Determination of mass concentration of tire and road wear particles (TRWP) in soil and sediments — Pyrolysis-GC/MS method
  • ISO/DIS 21490 Rubber and rubber products — Determination of 2-Mercaptobenzothiazole content by high performance liquid chromatography (HPLC)
  • ISO 21561-1:2015 Styrene-butadiene rubber (SBR) — Determination of the microstructure of solution-polymerized SBR — Part 1: 1H-NMR and IR with cast-film method
  • ISO 21561-2:2016 Styrene-butadiene rubber (SBR) — Determination of the microstructure of solution-polymerized SBR — Part 2: FTIR with ATR method
  • ISO/TS 22638:2018 Rubber — Generation and collection of tyre and road wear particles (TRWP) — Road simulator laboratory method
  • ISO/TS 22640:2018 Rubber — Framework for physical and chemical characterization of tyre and road wear particles (TRWP)
  • ISO/TS 22687:2018 Rubber — Framework for assessing the environmental fate of tyre and road wear particles (TRWP)
  • ISO 22768:2017 Rubber, raw — Determination of the glass transition temperature by differential scanning calorimetry (DSC)
  • ISO 22768 Raw rubber and rubber latex — Determination of the glass transition temperature by differential scanning calorimetry (DSC)
  • ISO/DIS 23075 Vulcanized rubbers — Determination of antidegradants by high-performance liquid chromatography
  • ISO 23233:2016 Rubber, vulcanized or thermoplastic — Determination of resistance to abrasion using a driven, vertical abrasive disc
  • ISO 23233:2016/AMD 1:2017 Rubber, vulcanized or thermoplastic — Determination of resistance to abrasion using a driven, vertical abrasive disc — Amendment 1
  • ISO 23337:2016 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using the Improved Lambourn test machine
  • ISO/CD 23508 Solution-polymerized SBR — Evaluation methods of viscoelastic properties
  • ISO 23529:2016 Rubber — General procedures for preparing and conditioning test pieces for physical test methods
  • ISO 23794:2015 Rubber, vulcanized or thermoplastic — Abrasion testing — Guidance
  • ISO/CD 24087 Vulcanized rubbers — Differential scanning calorimetry (DSC) — Determination of the glass transition temperature and enthalpy
  • ISO 24453:2008 Rubber — Acquisition and presentation of comparable single-point data
  • ISO 24454:2008 Rubber — Acquisition and presentation of comparable multi-point data
  • ISO 27727:2008 Rubber, vulcanized — Measurement of fatigue crack growth rate